All you need is a USB modem running version 1.6 or higher, with receivers carrying firmware
or higher! It's as easy as follows: Click on the receiver units icon on the right ">", click on
click on "Activate Link Mode". This will put the receiver (Version 4 onwards) in link mode, just
holding the black button on the side of the receiver. Now press and release the transmitter
you want to link. DONE
Light up your home and front entrance from the security of your car with the press of one button
keyring remote. Controlling your lighting from anywhere within a secure environment allows you
to have the
Yes, Qwik-Switch receivers can be linked to respond to multiple transmitters. Now you can place
switch at the top and the bottom of the stairs or entrance and exit of a passageway and these
both control the same light without any additional wiring.
A scene is a quick way of setting a group of lights to your favourite levels with one button
e.g Climb into bed and press "Sleep" ...this sets all your inside lighting to your desired
turns outside security lighting on.With a Qwik-Switch ScenePad you can create the scenes you
simplify your lifestyle...e.g "Leave","Arrive","Movie","Entertain"..etc
Qwik-Switch may be used in a wide variety of applications, from a single lighting circuit to
your whole home.
Energy-wise lighting, building remodelling and retro-fit projects can now be completed quickly
without all the wiring hassles.Qwik-Switch is the best solution for any installation where
running wires is
difficult or expensive.Virtually anything that turns off and on can be controlled by Qwik-Switch
Please be advised that Qwik-Switch, mains powered, devices are designed to operate of pure 220V 50Hz - Eskom supply.
This supply may vary in voltage and frequency by no more than 5%, any variations outside of this specification will void our warrantee.
UPS and backup power systems that generate 220v AC supply often make use of modified SINE wave generators, that result in unpure or noisy
SINE waves that can cause severe damage to equipment. Please contact us should you wish to install
any of our equipment under these conditions, we can then advise you on the correct remedial action.
If your Internet SIM card does not have the ability to send a text message
you will be required to temporarily make use of a SIM card that can. With a
text message activated SIM card, send a text message to the Cloud Hub mobile
number (default is 'internet'): apn:name. Replace 'name" with required APN name.
Then remove the text message activated sim card and replace with your internet
only sim card.
Once power is turned ON. The Cloud Hub will have a Quick double yellow flash .
A slow single yellow flash means the cloud is looking for signal.
Once the RED light is on and the GREEN light on , it’s connected to GPRS
GSM is the heart of your system so it needs to have 24hrs power.
GSM antenna must be as high as possible to get the best signal.
Make sure you have Data on your sim card that you installed in your GSM.
Now your Cloud Hub powered , Now take down the @ 12 digit ID on the Hub.
Go on to the Ecowatt Site www.ecowatt.co.za , Go to New User and entre your email
Address and Hub @ 12 digit ID number. Now go to your Gmail or Mail Account. Open the email
Sent from Ecowatt to you. click on the link. Once open you will be in your Dashboard.
Go to Device setup and add your device @ address there. Name you calling your device and the group you putting it in. click Ok when you finished.
Yes you can. Once you in your dashboard, go to manage site. click on your site and you
will see where you can put your rand costing and online/offline notification email alerts.
To add cell phone number click on the devices , you will see alerts with sms or email option . Add your details.
Once you have add all your devices, hover over your device and you will see it;s check and signal strength or click on each device. Once you clicked on a Device, you will see on the side icon ,
SIGNAL TEST. click on it and you will see your device checking in every 15 mins.
The repeater is very important as it helps devices to talk to each other. Try to get a constant power to this device. Once the repeater has power a RED light will be flash slowly.
Hold in the Link button till RED light start flashing fast. Release the link button.
Now set the repeater by putting the repeater twice. Always start the repeater number at 2,3,4 ect.
Check that your ct coils are plug in properly and if ports are not being used that a
port plug is plugged in so you don’t get floating current. In your dashboard make sure
you have enter the right coil size in your setting.
To determine what size CT to specify for your site. Take the current
that they require to be monitored and multiply this by 1.414(square root of 2 )
Then pick the range of CT’s we have and make sure the selected one is greater
than this value of your breaker.
If none of your device check in and you see a RED Clock showing you the period it has been off.
Is could be the Cellphone network or your GSM Unit has no power. Some device might of gone into
a lock up mood, where the device is constantly sending a radio signal and stop the other devices
to talk to the GSM. To solve this problem , switch power off to all devices ( from circuit breaker )
wait a minute and turn ON. Waiting for 15 mins for all devices to check in to the GSM.
Have you mounted the Temp unit in the correct place in your freezer? Mounting
of the device must be behind the blower . Temp housing must be on the outside
of the freezer and only the probe must be inside the freezer. The probe can
read from 0 celsius to -20 , any lower will put probe in a error.
All you need is a USB modem running version 1.6 or higher, with receivers
carrying firmware version 4 or higher! It's as easy as follows: Click on
the receiver units icon on the right ">", click on "Info", click on "Activate Link Mode".
This will put the receiver (Version 4 onwards) in link mode, just like holding the
black button on the side of the receiver. Now press and release the transmitter button
that you want to link. DONE
Ecowatt-Switch may be used in a wide variety of applications, from a single
lighting circuit to your whole home. Energy-wise lighting, building remodelling
and retrofit projects can now be completed quickly and effectively without all
the wiring hassles.Ecowatt-Switch is the best solution for any installation where
running wires is difficult or expensive.Virtually anything that turns off and on
can be controlled by Ecowatt-Switch products.